［1］
MARTIN H. Heat and mass transfer between impinging gas jets and solid surfaces[J]. Advances in Heat Transfer, 1977, 13 : 1-60.
[2] POLAT S, HUANG B, MUJUMDAR A S, et al. Numerical flow and heat transfer under impinging jets: A review[J]. Annual Review of Heat Transfer, 1989, 2(2): 157-197.
[3] JAMBUNATHAN K, LAI E, MOSS M A, et al. A review of heat transfer data for single circular jet impingement[J]. International Journal of Heat and Fluid Flow, 1992, 13(2): 106-115.
[4] LI Yongping, ZHANG Liang, LIN Qizhao, et al. Large eddy simulation of normally impinging round air-jet heat transfer at moderate Reynolds numbers[J]. Heat Transfer Engineering, 2017, 38(17): 1439-1448.
[5] 吴峰，王秋旺．脉动流条件下带突起内翅片管强化传热数值研究[J]．中国电机工程学报，2007，27(35)：108-112．
[6] 崔海亭，袁修干，姚仲鹏，等．异形凹槽螺旋槽管传热及流动阻力的实验研究[J]．中国电机工程学报，2003，23(6)：217-220．
[7] HRYCAK P. Heat transfer from impinging jets to a flat plate with conical and ring protuberances[J]. International Journal of Heat and Mass Transfer, 1984, 27(11): 2145-2154.
[8] WANG J, WANG X. The heat transfer optimization of conical fin by shape modification[J]. Chinese Journal of Chemical Engineering, 2016, 24(8): 972-978.
[9] ALAM T, KIM M H. Heat transfer enhancement in solar air heater duct with conical protrusion roughness ribs[J]. Applied Thermal Engineering, 2017, 126: 458-469.
[10] YEMIN O, WAE-HAYEE M, NARATO P, et al. The effect of conical dimple spacing on flow structure and heat transfer characteristics of internal flow using CFD[J]. IOP Conference Series: Materials Science and Engineering, 2017, 243： 012002.
[11] GUAN T, ZHANG J Z, SHAN Y. Conjugate heat transfer on leading edge of a conical wall subjected to external cold flow and internal hot jet impingement from chevron nozzle-Part 2: Numerical analysis[J]. International Journal of Heat and Mass Transfer, 2017,106: 339-355.
[12] GUAN T, ZHANG J Z, SHAN Y, et al. Conjugate heat transfer on leading edge of a conical wall subjected to external cold flow and internal hot jet impingement from chevron nozzle-Part 1: Experimental analysis[J]. International Journal of Heat and Mass Transfer, 2017, 106: 329-338.
[13] 马鹏程，唐志国，刘轻轻，等. 新型单圆锥体热沉单孔射流散热数值模拟[J]. 机械工程学报，2016，52(24)：136-141.
[14] 周嘉，唐志国，闵小滕，等. 微小单锥体热沉射流流动及换热特性研究[J]. 工程热物理学报，2017，38(11)：2399-2407.
[15] TANG Z G, LIU Q Q, LI H, et al. Numerical simulation of heat transfer characteristics of jet impingement with a novel single cone heat sink[J]. Applied Thermal Engineering, 2017,127: 906-914.
[16] ANSYS, Inc. Fluent 14.5: User’s Guide[M]. Canonsburg, PA, USA: ANSYS, Inc., 2012.
[17] ELEBIARY K, TASLIM M E. Experimental/numerical crossover jet impingement in an airfoil leading-edge cooling channel[C]// ASME 2011 Turbo Expo: Turbine Technical Conference and Exposition. New York: ASME, 2011: 1397-1409.
[18] BHAGWAT A B, SRIDHARAN A. Numerical simulation of oblique air jet impingement on a heated flat plate[J]. Journal of Thermal Science and Engineering Applications, 2016, 9(1): 011017.
[19] YANG L, REN J, JIANG H D, et al. Experimental and numerical investigation of unsteady impingement cooling within a blade leading edge passage[J]. International Journal of Heat and Mass Transfer, 2014, 71: 57-68.
[20] ZHANG D, QU H C, LAN J B, et al. Flow and heat transfer characteristics of single jet impinging on protrusioned surface[J]. International Journal of Heat and Mass Transfer, 2013, 58(1/2): 18-28.
[21] LEE D H, CHUNG Y S, KIM D S. Turbulent flow and heat transfer measurements on a curved surface with a fully developed round impinging jet[J]. International Journal of Heat and Fluid Flow, 1997, 18(1): 160-169.
()
() |
